rs2a thru RS2M surface mount fast recovery rectifier reverse voltage - 50 to 1000 volts forward current - 2.0 ampere note: 1.reverse recovery condition i f =0.5a,i r =1.0a,irr=0.25a 2.measured at 1mhz and applied reverse voltage of 4.0v d.c. 3.p.c.b. mounted with 0.2x0.2 ? (5.0x5.0mm) copper pad areas maximum ratings and electrical characteristics volts volts volts symbols units amp amps volts v rrm v rms v dc i (av) i fsm v f 2.0 50.0 1.3 operating junction and storage temperature range maximum repetitive peak reverse voltage maximum rms voltage maximum dc blocking voltage maximum average forward rectified current at t l =90 c peak forward surge current 8.3ms single half sine-wave superimposed on rated load (jedec method) maximum instantaneous forward voltage at 2.0a maximum dc reverse current t a =25 c at rated dc blocking voltage t a =125 c i r 5.0 200.0 r q ja c j t j , t stg 15.0 40.0 -50 to +150 pf c a m typical thermal resistance (note 3) c/w typical junction capacitance (note 2) maximum reverse recovery time (note 1) t rr 150 250 500 ns rs2a rs2b rs2d rs2g rs2j rs2k RS2M ratings at 25 c ambient temperature unless otherwise specified. single phase half-wave 60hz,resistive or inductive load,for capacitive load current derate by 20%. 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 case : jedec do-214aa molded plastic body over passivated chip terminals : solder plated, solderable per mil-std-750, method 2026 polarity : color band denotes cathode end mounting position : any weight the plastic package carries underwriters laboratory flammability classification 94v-0 for surface mounted applications low reverse leakage built-in strain relief,ideal for automated placement high forward surge current capability high temperature soldering guaranteed: 250 c/10 seconds at terminals features mechanical data glass passivated chip junction mdd electronic do-214a a (hsm b ) ( round lead ) h j e f g a b d c cathode band dimensions inches mm dim min max min max note a .078 .116 1.98 2.95 b .075 .089 1.90 2.25 c .002 .008 .05 .20 d ----- .02 ----- .51 e .035 .055 .90 1.40 f .065 .091 1.65 2.32 g .205 .224 5.21 5.69 h .160 .180 4.06 4.57 j .130 .155 3.30 3.94 mdd catalog number :0.005 ounce, 0.138 grams
ratings and characteristic curves rs2a thru RS2M mdd electronic average forward rectified current - amperes versus ambient temperature - c figure 2 forward derating curve 0 17550 75 100 125 0 .5 1.0 1.5 single phase, half wave 60hz resistive or inductive load amps c 150 2.0 2.5 3.0 junction capacitance - pf versus reverse voltage - volts instantaneous forward current - amperes versus instantaneous forward voltage - volts figure 1 typical forward characteristics 4 6 20 10 amps .4 .6 .8 1.0 1.2 1.4 .01 .02 .04 .06 .1 .2 .4 .6 1 2 25 c volts figure 3 junction capacitance .1 .2 1 .4 2 10 20 404 100 200 1 2 6 10 20 100 pf volts 60 40 4 400 1000 t j =25 c
ratings and characteristic curves rs2a thru RS2M mdd electronic t rr +0.5a 0 -0.25 -1.0 1cm set time base for 20/100ns/cm 25vdc 1 w 50 w 10 w oscilloscope note 1 pulse generator note 2 notes: 1. rise time = 7ns max. input impedance = 1 megohm, 22pf 2. rise time = 10ns max. source impedance = 50 ohms 3. resistors are non-inductive figure 5 reverse recovery time characteristic and test circuit diagram 1 100 4 0 15 30 45 8 figure 4 maximum non-repetitive forward surge current peak forward surge current - amperes versus number of cycles at 60hz - cycles amps cycles 2 6 10 20 60 80 40 60 75 90
|
